Question Details

(solution) NETW204 Class Project This project includes three phases. You


I need help with phase 3 of this project. Please let me know if u can help. I have attached phases 1 and 2 along with the original project sheet. It is due this sunday.


NETW204 Class Project

 

This project includes three phases. You need to complete Phase I before moving on to Phase II.

 

Likewise, you need to complete Phase II before moving on to Phase III or the final phase in the

 

project.

 

Hi-tech Net Corp. is operating in three locations in the United States. Their main office is located

 

in New York, NY. They have two branch offices located in Chicago, IL and Sacramento, CA.

 

You have just been hired as Hi-tech Net Corp.?s consulting engineer to implement their network

 

infrastructure. Both branch offices will be directly connected to the main office in NY via a

 

leased line circuit (point-to-point serial connection).

 

New York?s Office IP Information

 

The main office has four LAN segments: Executive, Engineering, Services, and

 

Native&Management. Each LAN segment is identified by a VLAN number as seen below. For

 

example: Executive: VLAN 15

 

Engineering: VLAN 25

 

Services: VLAN 35

 

Native&Management: VLAN 999 The organization is using the following network address in NY: 10.150.0.0/16. Executive: 60 computers only including future growth in this number

 

Engineering: 80 computers only including future growth in this number

 

Services: 115 computers including future growth in this number

 

Native&Management: 12 computers including future growth in this number *** Future growth means that we already take growth into consideration. Do not try to

 

estimate or add more IP addresses than necessary to avoid getting an incorrect subnet.

 

Illinois? Office IP Information

 

The IL branch has three LAN subnets with 45 IP addresses on each subnet. They use the

 

following network address to obtain the required IL subnets: 10.150.100.0 /25.

 

California?s Office IP Information

 

The CA branch has three LAN subnets with 25 IP addresses on each subnet. They use the

 

following network address to obtain the required CA subnets: 10.150.200.0 /25. PHASE I (20 points total)?Due Week 3

 

Tasks to Do.

 

Task 1: Subnet the 10.150.0.0/16 network for NY and assign the first nonzero subnets to

 

Services followed by Engineering. You may need to re-subnet for Executive and

 

Native&Management subnets to avoid wasting IP addresses. Ensure that you re-subnet only the

 

first unused subnet and nothing else. Assign the nonzero subnets to Executive and

 

Native&Management. (5 points)

 

New York Office IP

 

VLAN 15

 

VLAN 25

 

VLAN 35

 

VLAN 99 IP Address Subnet Mask Network Address Task 2: Subnet the 10.150.100.0 /25 network for IL and assign the last IP address on the first

 

three nonzero subnets to the Loopback 1, Loopback 2, and Loopback 3 interfaces of the router.

 

We will use a loopback or virtual interface to simulate the LAN subnets. This will speed up

 

configuration and allows us to create our topology without rewiring. (3 points)

 

Illinois Branch IP

 

Loopback 1

 

Loopback 2

 

Loopback 3 IP Address Subnet Mask Network Address Task 3: Subnet the 10.150.200.0 /25 network for CA and assign the last IP address on the first

 

three nonzero subnets to the Loopback 1, Loopback 2, and Loopback 3 interfaces of the router.

 

We will use a loopback or virtual interface to simulate the LAN subnets. This will speed up

 

configuration and allows us to create our topology without rewiring. (3 points)

 

California Branch IP

 

Loopback 1

 

Loopback 2

 

Loopback 3 IP Address Subnet Mask Network Address Task 4: Use the following network address (10.1.255.0/25) to find the WAN subnets between NY

 

and IL and NY and CA respectively. Note that there are only two IP addresses per subnet for

 

each WAN link. Assign the first WAN subnet to NY to IL and the second WAN subnet to NY to CA.

 

(2 points) WAN Subnets

 

NY to IL

 

NY to CA IP Address Subnet Mask Network Address Task 5: Use Microsoft Visio to design the current network topology. Remember to use Loopback

 

interfaces for the subnets in NY, IL, and CA. Use point-to-point interfaces to connect the remote

 

branch offices to NY. See the sample network diagram below. Replace the phrase ?IP Address?

 

by the correct IP address for each interface on the routers. Include the WAN IP addresses on the

 

diagram as well. (7 points) First Major Deliverable in the Project: IP scheme for all three locations (fill in the IP tables

 

above) and the Visio Diagram. PHASE II (30 points total)?Due Week 5

 

Now that you have completed your first major deliverable in the project, let us move on to the

 

next phase in the project. You need to plan to implement the network. You will configure the

 

switches first. Task 1: Configure SW1. (3.5 points possible)

 

Configuration Task

 

Switch name

 

Secret Password

 

Disable DNS lookup

 

Username and Password

 

Message of the Day

 

(MOTD) Banner

 

VTY

 

Encrypt the clear text

 

passwords

 

Create the required

 

VLANs.

 

Assign the management

 

IP address.

 

Enable the 802.1Q Trunk

 

ports.

 

Configure all other ports

 

as access ports.

 

Assign F0/3 to the

 

correct VLAN as per the

 

diagram.

 

Shutdown all unused

 

ports. Required Information

 

SW1

 

Netw204

 

User= Admin1, Password=cisco123

 

Unauthorized Access is Highly

 

Prohibited!

 

Enable SSH and Disable Telnet.

 

Use the correct command to encrypt

 

clear text passwords.

 

Use the information provided to create

 

the VLANs.

 

Assign the IP Address just before the

 

last valid IP Address on the

 

Native&Management VLAN. VLAN 999

 

is the Native VLAN.

 

Use the correct switchport command to

 

set the Trunk port.

 

Use the interface range command. Points

 

¼

 

¼

 

¼

 

¼

 

¼

 

½

 

¼

 

¼

 

¼ ¼

 

¼ See the network diagram you drew for

 

part 1. ¼ Disable all unused ports in software. ¼ Task 2: Configure SW2. (3.5 points possible)

 

Configuration Task

 

Switch name

 

Secret Password Required Information

 

SW2

 

Netw204 Points

 

¼

 

¼ Disable DNS lookup

 

Username and Password

 

Message of the Day

 

(MOTD) Banner

 

VTY

 

Encrypt the clear text

 

passwords

 

Create the required

 

VLANs.

 

Assign the management

 

IP address.

 

Enable the 802.1Q Trunk

 

ports.

 

Configure all other ports

 

as access ports.

 

Assign F0/3 to the

 

correct VLAN as per the

 

diagram.

 

Shutdown all unused

 

ports. User= Admin1, Password=cisco123

 

Unauthorized Access is Highly

 

Prohibited!

 

Enable SSH and Disable Telnet.

 

Use the correct command to encrypt

 

clear text passwords.

 

Use the information provided to create

 

the VLANs.

 

Assign the IP Address just before the

 

last valid IP Address on the

 

Native&Management VLAN. VLAN 999

 

is the Native VLAN.

 

Use the correct switchport command to

 

set the Trunk port.

 

Use the interface range command. ¼

 

¼

 

¼

 

½

 

¼

 

¼

 

¼ ¼

 

¼ See the network diagram you drew for

 

part 1. ¼ Disable all unused ports in software. ¼ Task 3: Configure the NY Router. (6 points)

 

Configuration Item or Task Required Information Points Configure 802.1Q subinterface .

 

15 on G0/1 Description Executive LAN

 

Assign VLAN 15.

 

Assign the last valid IP address to this

 

interface. ½ Configure 802.1Q subinterface .

 

25 on G0/1 Description Engineering LAN

 

Assign VLAN 25.

 

Assign the last valid IP address to this

 

interface. ½ Configure 802.1Q subinterface .

 

35 on G0/1 Description Services LAN

 

Assign VLAN 35.

 

Assign the first available address to

 

this interface. ½ Configure 802.1Q subinterface .

 

999 on G0/1 Description Native&Management

 

LAN

 

Assign VLAN 999.

 

Assign the last valid IP address to this

 

interface. ½ Activate Interface G0/1 Bring up interfaces ½ OSPF Process ID 204 ½ Router ID 1.1.1.1 ½ Advertise directly connected

 

networks. Use classless network addresses

 

Assign all directly connected

 

networks to Area 0 ½

 

½ Set all LAN interfaces as passive. Type necessary commands to do so. Change the default cost

 

reference bandwidth to support

 

Gigabit interface calculations. 1000 Set the serial interface

 

bandwidth. 768 Kb/s Adjust the metric cost of S0/0/0. Cost: 7500 ½

 

½

 

½ Task 4: Configure the IL Router. (4 points)

 

Configuration Task Required Information Points

 

½ Assign IP addresses to appropriate interfaces

 

including Loopback and serial interfaces. ½

 

Activate the nonLoopback interfaces.

 

½

 

OSPF Process ID 204

 

½ Router ID 2.2.2.2 Advertise directly connected networks. Use classless network

 

addresses.

 

Assign interfaces to Area 0.

 

Use a single summary address

 

for the LAN (loopback)

 

interfaces. ½ ½

 

Set all LAN (Loopback) interfaces as passive.

 

Change the default cost reference bandwidth

 

to support Gigabit interface calculations. ½

 

1000

 

½ Set the serial interface bandwidth. 256 Kb/s Note: You will probably notice that all the Loopback IP addresses show up as /32. To change

 

that /32 to the real subnet mask of the Loopback interfaces you need to type the following

 

command on each Loopback interface in the routers.

 

Interface Loopback 1

 

ip ospf network point-to-point

 

Task 5: Configure the CA Router. (4 points) Configuration Task Required Information Points

 

½ Assign IP addresses to appropriate interfaces

 

including Loopback and serial interfaces. ½

 

Activate the nonLoopback interfaces.

 

½

 

OSPF Process ID 204

 

½ Router ID 3.3.3.3 Advertise directly connected networks. Use classless network

 

addresses.

 

Assign interfaces to Area 0.

 

Use a single summary address

 

for the LAN (loopback)

 

interfaces. ½ ½

 

Set all LAN (Loopback) interfaces as passive.

 

Change the default cost reference bandwidth

 

to support Gigabit interface calculations. ½

 

1000

 

½ Set the serial interface bandwidth. Task 6: Verify OSPF Configuration (6 points) 256 Kb/s Question Points Type the command that displays all connected OSPFv2 routers. Capture the

 

output for your project and explains what you see. 1 Type the command that displays the OSPF process ID, router ID, routing

 

networks, address summarization, and passive interfaces configured on a

 

router. Capture the output for your project and explain what you see. 1 What command displays only OSPF routes? 1 What command displays detail information about the OSPF interfaces,

 

including the authentication method? 1 What command displays the OSPF link states types? 1 What command displays the OSPF database? 1 Task 7: Summarize the output of the commands used in Task 6. How can you tell that the

 

network is working correctly? (3 points) PHASE III (70 Points Total)?Due Week 7

 

Task 1: Configure the NY router as a DHCPv4 server for the executive and engineering VLAN. (4

 

points) Configuration Task Required Information Points Reserve the first 10 IP addresses

 

in VLAN 15 for static

 

configurations. (1 point) Reserve the first 10 IP addresses

 

in VLAN 25 for static

 

configurations. (1 point) Create a DHCP pool for VLAN 15. Name: EXECUTIVE

 

DNS-Server: 192.168.1.45

 

Domain-Name: hitech.net

 

Set the default gateway. (1 point) Create a DHCP pool for VLAN 25. Name: ENGINEERING

 

DNS-Server: 192.168.1.45

 

Domain-Name: engineering.com

 

Set the default gateway. (1 point) Task 2: Restrict Access to the VTY Lines to only come from Native&Management VLAN. (15

 

points)

 

Configuration Task

 

Configure a named access list to only allow

 

Native&Management VLAN to SSH to the routers. Required Information

 

ACL Name: NETMGMT Points

 

5 Apply the named ACL to the VTY lines. 5 Verify ACL is working as expected. 5 Task 3: Configure static and dynamic NAT on NY. (25 points)

 

Configuration Task Required Information Points Create a local database with one

 

user account. Use the command

 

username webadmin privilege 15

 

secret cisco123. Username: webadmin

 

Password: cisco123

 

Privilege level: 15 5 Enable HTTP server service. ip http ? 2 Configure the HTTP server to use

 

the local database for

 

authentication. ip http authentication ? Create a static NAT to the web

 

server. Inside Global Address: 209.107.23.66 --> 2 Configure NY?s Loopback 0

 

interface with the following IP

 

address. This is a simulated

 

internal web server. 192.168.1.200/32 Assign the inside and outside

 

interface for the static NAT. 192.168.1.200 209.107.23.66 /26 2 1 1 Configure the dynamic NAT inside

 

private ACL. Access List: 10

 

Allow the executive and engineering

 

networks on NY to be translated.

 

Allow a summary of the LANs (loopback)

 

networks on IL and CA to be translated.

 

Do not allow the Services and

 

Native&Management VLANs to be

 

translated. 5 Define the pool of usable public

 

IP addresses. Pool Name: THE_NET

 

Pool of addresses include:

 

209.107.23.68 ? 209.107.23.75 5 Define the dynamic NAT

 

translation. 2 Task 4: Secure the network services. (16 points) Configuration Task

 

Configure an extended ACL to allow Internet hosts WWW access to the

 

simulated web server on NY by accessing

 

the static NAT address (209.107.23.66 /26)

 

that you configured in Task 3; allow Internet hosts DNS access to the

 

simulated web server on NY by accessing

 

the static NAT address (209.107.23.66 /26)

 

that you configured in Task 3; and prevent traffic from the Internet from

 

pinging internal networks, while continuing

 

to allow LAN interfaces to ping the Internet

 

hosts.

 

Apply ACL to the appropriate interface(s). Required Information

 

ACL No.: 105 Points

 

10 6 Task 5: Verify that your project meets the above requirements. Write a summary of what you

 

did and explain what you have learned in the process. (10 points)

 


Solution details:
STATUS
Answered
QUALITY
Approved
ANSWER RATING

This question was answered on: Jan 30, 2021

PRICE: $15

Solution~0001018395.zip (25.37 KB)

Buy this answer for only: $15

This attachment is locked

We have a ready expert answer for this paper which you can use for in-depth understanding, research editing or paraphrasing. You can buy it or order for a fresh, original and plagiarism-free solution (Deadline assured. Flexible pricing. TurnItIn Report provided)

Pay using PayPal (No PayPal account Required) or your credit card . All your purchases are securely protected by .
SiteLock

About this Question

STATUS

Answered

QUALITY

Approved

DATE ANSWERED

Jan 30, 2021

EXPERT

Tutor

ANSWER RATING

GET INSTANT HELP/h4>

We have top-notch tutors who can do your essay/homework for you at a reasonable cost and then you can simply use that essay as a template to build your own arguments.

You can also use these solutions:

  • As a reference for in-depth understanding of the subject.
  • As a source of ideas / reasoning for your own research (if properly referenced)
  • For editing and paraphrasing (check your institution's definition of plagiarism and recommended paraphrase).
This we believe is a better way of understanding a problem and makes use of the efficiency of time of the student.

NEW ASSIGNMENT HELP?

Order New Solution. Quick Turnaround

Click on the button below in order to Order for a New, Original and High-Quality Essay Solutions. New orders are original solutions and precise to your writing instruction requirements. Place a New Order using the button below.

WE GUARANTEE, THAT YOUR PAPER WILL BE WRITTEN FROM SCRATCH AND WITHIN A DEADLINE.

Order Now